Pinouts >  Разъемы штатных автомагнитол Mitsubishi  >  Outlander pinouts
20 pin Mitsubishi Head Unit connector layout
Разъем 20 pin Mitsubishi Head Unit
p/n 8740A103 NR-201 EM0LNDA-T

Amplifier is 8701A813 (CV-0MW6P45-2).

This pinout should be also for (not tested):

  • 8740A104 (NR-201AM0LNDA-T)
  • 8740A046 (NR-201AM0PJRA-T)
  • 8740A100 (NR-201EM0LND0-T)
  • 8740A103 (NR-201EM0LNDA-T)
  • 8740A121 (NR-201EM0LNDG-T)
  • 8740A125 (NR-201EM0LNDN-T)
  • 8740A098 (NR-201UM0LND0-T)
  • 8740A105 (NR-201GM0LNDA-T)
  • 8740A102 (NR-201JM0LNDA-T)
  • 8740A106 (NR-201RM0LNDA-T)
  • 8740A101 (NR-201XM0LND0-T) 
  • 8740A099 (NR-201YM0LND0-T)

Connector (20-pin,to white receptacle), harness connector view

Terminal No. Signal symbol Check item Check condition Terminal voltage
1 ACC ACCESSORY (+) Ignition switch: ACC position System voltage (DC)
2 REM+ REMOCON Ignition switch: ACC position 3.3V (DC)
3 CANH AUDIO:CAN+ - -
5 RR+ SPEAKER RR (+) When the sound is output 0 - System voltage (AC)
6 DFR+ SPEAKER FR (+) When the sound is output 0 - System voltage (AC)
7 RL+ SPEAKER RL (+) When the sound is output 0 - System voltage (AC)
8 DFL+ SPEAKER FL (+) When the sound is output 0 - System voltage (AC)
9 ILL+ ILLUMINATION (+) Tail lamp switch: ON System voltage (DC)
10 +B2 BATTERY (+) Always System voltage (DC)
11 REED VEHICLE SPEED PULSE Ignition switch: ON 0 - System voltage (pulse)
12 REM- REMOCON GND Always 1 V or less
13 CANL AUDIO:CAN (-) - -
14 ANT+ ANTENNA +B Ignition switch: ACC position System voltage (DC)
15 RR- SPEAKER RR (-) When the sound is output 0 - System voltage (AC)
16 DFR- SPEAKER FR (-) When the sound is output 0 - System voltage (AC)
17 RL- SPEAKER RL (-) When the sound is output 0 - System voltage (AC)
18 DFL- SPEAKER FL (-) When the sound is output 0 - System voltage (AC)
19 ILL- ILLUMINATION (-) Always 1 V or less
20 GND2 POWER GND Always 1 V or less

Connector (18-pin, to white), harness connector view

Terminal No. Signal symbol Check item Check condition Terminal voltage
24 AAL+ LOCAL CAN (+) Mitsubishi Eclipse Cross (2018+) only  
26 TIR+ IE-BUS INPUT RIGHT (+) - -
27 TIL+ IE-BUS INPUT LEFT (+) - -
28 AMPO IE-BUS POWER ON Ignition switch: ACC position 1 V or less
29 D-S+ IE-BUS (+) Ignition switch: ACC position More than 120mV
32 AA- LOCAL CAN (-) Mitsubishi Eclipse Cross (2018+) only  
35 TIR- IE-BUS INPUT RIGHT (-) - -
36 TIL- IE-BUS INPUT LEFT (-) - -
38 D-S- IE-BUS (-) Ignition switch: ACC position More than 120mV

Connector (8-pin, to gray)

Terminal No. Signal symbol Check item Check condition Terminal voltage
41 CACC VCC (RC6.5V)
  • Ignition switch: ON position
  • Selector lever or Shift lever : R position
5.8 - 7.0V (DC)
45 CGND GND (RC) Always 1 V or less
46 CMP+ CAMERA SIGNAL
  • Ignition switch: ON position
  • Selector lever or Shift lever : R position
1 Vp-p (AC)
47 CMP- SHIELD (CAMERA) Always 1 V or less
48 GND GND (RC) Always  1 V or less

Connector (16pin, to gray)

Terminal No. Signal symbol Check item Check condition Terminal voltage
56 MGND SHIELD (MIC) Always 1 V or less
57 SNSE MIC DETECT Always 1 V or less
63 MIC- MIC GND Always 1 V or less
64 MIC+ MIC SIGNAL Ignition switch: ACC position 1 V or less

Pins not mentioned are not connected 

18 pin Mitsubishi Head Unit connector layout
Разъем 18 pin Mitsubishi Head Unit
На эту распиновку нет ни одного отзыва! Если вы знаете, правильная она или нет, - нажмите на соответствующую кнопку ниже.

Эта распиновка

Additional connector №3

8 pin Mitsubishi Head Unit Camera connector layout
Разъем 8 pin Mitsubishi Head Unit Camera

Additional connector №4

16 pin Honda, Mitsubishi Head Unit Aux connector layout
Разъем 16 pin Honda, Mitsubishi Head Unit Aux
Copyright © 2000-2024 by pinouts.ru team, except user uploaded images.
No portion of this webpage may be reproduced in any form without visible link to pinouts.ru .
Efforts have been made to ensure this page is correct, but it is the responsibility of the user to verify the data is correct for their application.
Change privacy settings