Nokia Pop Port (DKU-5)

Started by Ofer, Feb 22, 2005, 14:04

Previous topic - Next topic
|

Ofer

Hi,

Does anyone knows how to get power from the Nokia 6100 ?

There is some sequence on the ACI Pin ...

Thanks,

Ofer.

fernando

1 |*| 2|3|4|5|6|7|8|9|10|11|12|13|14|*

1 - Vin - Charger input
2- GND - Charger output
3 - ACI - Auto-connect Ignition
4 - Vout -
5 - USB Vbus - Also act as USB power detection?
6 - Fbus Rx/USB D+ - USB exists at least in NOKIA 2280, 3586,7610, 6225
7 - Fbus Tx/USB D-  - USB exists at least in NOKIA 2280, 3586,7610, 6225
8 - GND - Data GND (Logic)
9 - VMic-  - Audio IN - Ext. Mic input negative
10 - VMic+  - Audio IN - Ext. Mic input positive
11 - Hs Ear L-  - Audio Out - Ext. audio out: left-negative
12 - Hs Ear L+  - Audio Out - Ext. audio out: left-positive
13 - Hs Ear R-  - Audio Out - Ext. audio out: right-negative
14 - Hs Ear R+  - Audio Out - Ext. audio out: right-positive
* - GND - Shield GND in cavities

Enjoy!.


iced-tea

Hi!
I've tried to connect the the pin-out from pop-port to usb port directly as follows:
pop-port                                   to ------>    USB
3 - ACI - Auto-connect Ignition ---> short to 4
4 - Vout                                    
5 - USB Vbus                            to -------> 1 - Vcc USB
6 - Fbus Rx/USB D+                  to -------> 2 - D+ USB
7 - Fbus Tx/USB D-                   to -------> 3 - D- USB
8 - GND - Data GND (Logic)       to -------> 4 - GND USB
the connection is OK, but the system (WinXP2) recognized as USB unkown.

Does anyone can advise what should I do? I have installed the DKU-5 driver before connecting the device, my phone is Nokia 3120.

Thank you very much!
Steve "iced-tea"

casual

Congratulations iced-tea!!!!!
You have made a DKU-2 cable !!!!


Detection of usb device as made because you close the power line of usb.
When this occurs, the usb controller interrogates the device in order to load the required drivers.
If this interrogation is not a success, the system is not capable to determine what kind of device is attached.

You can try to connect your bread toaster to usb port and the result is the same.

Nokia 3120 is not a usb device. (i think your toaster is not too)

Avi Feldman

Hi,
i am doing a project in which i need to get power supply from a cellular phone....
i bought a cable dku5 and conected to the popport, i messered the power and it was only 0.7 V . i used the pinout diagram u wrote in this site using pins 4 & 8 but i cant get the vdd which is 3 v in Nokia 3120.

If some now it will help me .

Thanks Avi.

avi feldman

Hi,
i am doing a project in which i need to get power supply from a cellular phone....
i bought a cable dku5 and conected to the popport, i messered the power and it was only 0.7 V . i used the pinout diagram u wrote in this site using pins 4 & 8 but i cant get the vdd which is 3 v in Nokia 3120.

If some now it will help me .

Thanks Avi.

|