May 22, 2019, 17:12

Recent posts

Pages 1 ... 8 9 10
91
Interfaces, Pinouts, Cables / Old Computer PinOuts
Last post by AzWiz - Mar 24, 2015, 13:26
If there is any interest, I have pinouts and schematics of various S-100 bus computers.  I'd be happy to post or otherwise supply to the site sysop.:o
92
Interfaces, Pinouts, Cables / Old Computer PinOuts
Last post by AzWiz - Mar 24, 2015, 13:25
If there is any interest, I have pinouts and schematics of various S-100 bus computers.  I'd be happy to post or otherwise supply to the site sysop.:o
93
Interfaces, Pinouts, Cables / Old Computer PinOuts
Last post by AzWiz - Mar 24, 2015, 13:24
If there is any interest, I have pinouts and schematics of various S-100 bus computers.  I'd be happy to post or otherwise supply to the site sysop.:o
94
The connector shown in the attached photos is a 2-pin battery-power connector for a Walkera 2D Gimbal (used in aerial photography). I measured the pin separation at 2.5mm.  It is faintly stamped with the characters "83 XS". A google search has not identified it.

I would be grateful if anyone knows what it is - and even where I can get some.

Many thanks


95
The connector shown in the attached photos is a 2-pin battery-power connector for a Walkera 2D Gimbal (used in aerial photography). I measured the pin separation at 2.5mm.  It is faintly stamped with the characters "83 XS". A google search has not identified it.

I would be grateful if anyone knows what it is - and even where I can get some.

Many thanks


96
this is the carkit http://pinouts.ru/CellularPhonesCables/nokia_ca-27_cable_pinout.shtml don't know on which pins to connect the Jack stereo cable. Any ideeas?
97
Interfaces, Pinouts, Cables / Jack 3.5 mm audio to rj50
Last post by Ceatza91 - Mar 20, 2015, 10:04
Hey dudes,as the title says, is it possible to make this kind of cable? I have an nokia carkit, with an rj50 connector, and want to adapt it so i can use my smartphone instead of that verry old nokia phone in my car.
98

I work in a general store (we'll leave it at that) in a small town, and the other night one of our regular customers came in with her son in the hopes of finding a charge cable for a Droid watch someone had given him. Unfortunately, they didn't give him a cable for it. When I asked to see the watch, he showed it to me and I began going through the ones we have to see if there were any that were compatible sized. There is no maker mark on the back or the bezel, as you can see from this one picture, so I couldn't tell for sure exactly what it was I was looking at or for, but I noticed rather fast that no chargers we carry would fit it.

This kid's family are good people, working hard and trying to make ends meet in a town that is feeling the hit from the oil prices tanking like they did, and he doesn't often see odd tech like this. I actually think he'd be the first kid in his school with one, putting him above even the old money kids. He's just like his parents, a bit of spunk but good-natured, and I want to try and help with both identification and getting him the right cable for it.

I apologize for the crappy pic, I have hand tremors that make getting good shots with my phone's camera difficult, but I assure you it IS better than normal. The port at first glance appears to be a Droid type, it's rather flat, but it's a bit longer than a standard micro jack. If needed, I can also post another slightly fuzzy picture of that. If I can get my phone to regurgitate it.
99
Hello
I am stuck in a no man's land and any suggestion would be greatly appreciated. I cannot find a system interface cable for Sony Ericsson G36e FWT. It seems it has 18 pins on one side and it is, as usual, a proprietary design. If someone could help me with it's layout, technical specs, similar cable I would appreciate it.
I cannot rewrite the firmware without that piece of cable.
Thank you very much
Bogdan
100
Hello
I am stuck in a no man's land and any suggestion would be greatly appreciated. I cannot find a system interface cable for Sony Ericsson G36e FWT. It seems it has 18 pins on one side and it is, as usual, a proprietary design. If someone could help me with it's layout, technical specs, similar cable I would appreciate it.
I cannot rewrite the firmware without that piece of cable.
Thank you very much
Bogdan
Pages 1 ... 8 9 10