Toshiba e330 распиновка

[mr. Zorg]

Приветствую всех! Господа нужна распиновка разъёма на КПК Toshiba e330. Может поделится кто? По поиску нашёл только на 800\805 но она не подходит у 800-40 контактов, а у 330-26.

[mr. Zorg]

Вот нарыл... Может понадобится кому... Ещё не проверял, проверю сообщу....
Note pin 26 is on the left, and pin 1 is on the right. (Also note that Pin 1 is clearly identitfied on the connectors...)

Here is what I have confirmed from my expansion pack and the cradle:

Pin #           Action
1               +5 V USB
2                - Data USB (slave)
3                 + Data USB (slave)
4                GND USB
5                +5V (VDD, power out for USB Host) - see notes below
6                 - Data USB (Host)
7                  USB internal / external power toggle (used with 4.7k ohm resistor & pin 15 below)
                  - see notes below
8                  + Data USB (Host)
9                   through 14 ?? Video ?? - Don't know
15                  USB internal / external power toggle (used with 4.7k ohm resistor & pin 7 above)
                     - see notes below  
16 & 18           GND USB
17                  ?? Don't know
19,20,21,22    +5 V (VCC, system power to e740)
23,24,25,26    GND (system power to the e740)

Please help me fill in the missing Video pins!!


Pin 7 & 15 - USB External vs. Internal Power

Use this trick with the Franken-Cradle and Ultra-Cradle designs to tell the cradle to allow the e7xx to power the hub or to tell external power to power the hub.

To toggle e7xx power for the USB hub (without external power) - a 4.7k ohm resistor needs to be connected between pins #7 and #15.

One user emailed me his method to implement this -
1st - Connect pin #7 and pin #15 with a 4.7K resistor directly on the upper connector.
2nd - use a double relay to switch both +5V and ground. As on the Franken-Cradle and Ultra-Cradle designs, the relay is driven by external power. In default position it connects USB power and ground from the PPC. For that connect pin #5 (+5V) with
one relay switch defaults position. Connect ground from the PWB to the other switch in default position, it's connected to the upper connector trough the flex cable with the PPC ground.

If external power is connected, the switches go to connect power and ground for USB Hub directly from the external power connector.

[Anonymous]

Вот нарыл... Может понадобится кому... Ещё не проверял, проверю сообщу....
Note pin 26 is on the left, and pin 1 is on the right. (Also note that Pin 1 is clearly identitfied on the connectors...)

Here is what I have confirmed from my expansion pack and the cradle:

Pin #           Action
1               +5 V USB
2                - Data USB (slave)
3                 + Data USB (slave)
4                GND USB
5                +5V (VDD, power out for USB Host) - see notes below
6                 - Data USB (Host)
7                  USB internal / external power toggle (used with 4.7k ohm resistor & pin 15 below)
                  - see notes below
8                  + Data USB (Host)
9                   through 14 ?? Video ?? - Don't know
15                  USB internal / external power toggle (used with 4.7k ohm resistor & pin 7 above)
                     - see notes below  
16 & 18           GND USB
17                  ?? Don't know
19,20,21,22    +5 V (VCC, system power to e740)
23,24,25,26    GND (system power to the e740)

Please help me fill in the missing Video pins!!


Pin 7 & 15 - USB External vs. Internal Power

Use this trick with the Franken-Cradle and Ultra-Cradle designs to tell the cradle to allow the e7xx to power the hub or to tell external power to power the hub.

To toggle e7xx power for the USB hub (without external power) - a 4.7k ohm resistor needs to be connected between pins #7 and #15.

One user emailed me his method to implement this -
1st - Connect pin #7 and pin #15 with a 4.7K resistor directly on the upper connector.
2nd - use a double relay to switch both +5V and ground. As on the Franken-Cradle and Ultra-Cradle designs, the relay is driven by external power. In default position it connects USB power and ground from the PPC. For that connect pin #5 (+5V) with
one relay switch defaults position. Connect ground from the PWB to the other switch in default position, it's connected to the upper connector trough the flex cable with the PPC ground.

If external power is connected, the switches go to connect power and ground for USB Hub directly from the external power connector.