HDD and other storage devices connectors pinouts  > Apple pinouts
Used on PowerBooks for the 2.5" drives. The internal hard disk has a 48-pin connector that carries both the ATA signals and the power for the drive.
Pin Name Dir Description
1/RESET-->Reset
2GND---Ground
3DD7<->Data 7
4DD8<->Data 8
5DD6<->Data 6
6DD9<->Data 9
7DD5<->Data 5
8DD10<->Data 10
9DD4<->Data 4
10DD11<->Data 11
11DD3<->Data 3
12DD12<->Data 12
13DD2<->Data 2
14DD13<->Data 13
15DD1<->Data 1
16DD14<->Data 14
17DD0<->Data 0
18DD15<->Data 15
19GND---Ground
20KEY-Key (Pin missing)
21DMARQ?DMA Request
22GND---Ground
23/DIOW, /STOP-->Write Strobe
24GND---Ground
25/DIOR, /HDMARDY, HSTROBE-->
26GND---Ground
27IORDY, /DDMARDY, DSTROBE<--I/O Ready,...
28CSEL?
29/DMACK?DMA Acknowledge
30GND---Ground
31INTRQ<--Interrupt Request
32/IOCS16?obsolete, not used
33/DA1-->Address 1
34/PDIAG, /CBLID?Passed Diagnostics
35/DA0-->Address 0
36/DA2-->Address 2
37/CS0-->
38/CS1-->
39/DASP-->
40GND---Ground
41+5V LOGIC
42+5V MOTOR
43GNDGround
44Reserved

/DA(0?2) Device address; used by the computer to select one of the registers in the ATA drive. For more information, see the descriptions of the CS0 and CS1 signals.

DD(0?15) Data bus; buffered from IOD(16?31) of the computer?s I/O bus. DD(0?15) are used to transfer 16-bit data to and from the drive buffer. DD(8?15) are used to transfer data to and from the internal registers of the drive, with DD(0?7) driven high when writing.

/CBLID The host checks this signal after Power On or hardware reset to detect whether an 80-conductor cable is present.

/CS0 Register select signal. It is asserted low to select the main task file registers. The task file registers indicate the command, the sector address, and the sector count.

/CS1 Register select signal. It is asserted low to select the additional control and status registers on the ATA drive.

CSEL Cable select; not available on the iBook.

/DASP Device active or slave present; not available on the iBook.

/DDMARDY Drive ready to receive Ultra DMA data.

/DIOR I/O data read strobe.

/DIOW I/O data write strobe.

/DMACK Used by the host to initiate a DMA transfer in response to DMARQ.

DSTROBE Strobe for Ultra DMA data transfers to host.

/HDMARDY Ultra DMA data ready.

HSTROBE Strobe for Ultra DMA data transfers from host.

IORDY I/O ready; when driven low by the drive, signals the CPU to insert wait states into the I/O read or write cycles.

/IOCS16 I/O channel select; not used on this computer (pulled low by 1 kilohm resistor).

DMARQ Asserted by the device when it is ready to transfer data to or from the host.

INTRQ Interrupt request. This active high signal is used to inform the computer that a data transfer is requested or that a command has terminated.

/PDIAG Asserted by device 1 to indicate to device 0 that it has completed the power-on diagnostics; not available on the iBook.

/RESET Hardware reset to the drive; an active low signal.

/STOP Stop request; an active low signal.

Key This pin is the key for the connector.

48 pin Apple ATA connector layout
48 pin Apple ATA connector
at the Apple computer
There are no any reports for this pinout! You may rate this document by clicking the button below.

Is this pinout
Apple PowerBook ATA visual pinout:
Apple PowerBook ATA diagram
click to enlarge
Source(s) of this and additional information: Apple iBook developer note
This page contain parts under Copyright © 2000-2015 by pinouts.ru team.
No portion of this webpage may be reproduced in any form without providing visible HTML link to Pinouts.ru . Webmaster permission required in any other cases.
Efforts have been made to ensure this page is correct, but it is the responsibility of the user to verify the data is correct for their application.