Hardware pinouts information and cables schemes

Cisco Console (9) cable specification users reports and reviews

[Discuss at the forum] [SUBMIT new pinout]

There are 47 approved reports in our database

Date Content
User opinion Comment Approved by moderator?
CORRECTDB9 pin 5 (GND) is linked with pins 4 & 5 on RJ45 APPROVED
CORRECTRIGHT.pins 4 and 5 to groundAPPROVED
CORRECTWorks like a dreamAPPROVED
2008-11-14 04:49:52rev. 5CORRECTYep, works nicely.APPROVED
2009-03-10 03:04:22rev. 5CORRECTnoneAPPROVED
2009-03-29 07:22:25rev. 5CORRECTAPPROVED
2009-12-21 19:39:23rev. 6CORRECTAPPROVED
2010-03-25 11:54:32rev. 6CORRECTAPPROVED
2010-04-06 21:54:49rev. 6CORRECTAPPROVED
2010-05-28 04:45:04rev. 6CORRECTAPPROVED
2010-10-22 18:20:16rev. 6CORRECTYes , it does workAPPROVED
2011-10-06 18:39:37rev. 6CORRECTAPPROVED
2011-12-09 23:10:05rev. 6CORRECTAPPROVED
2012-01-19 11:38:12rev. 6CORRECTAPPROVED
2012-01-21 18:58:24rev. 6CORRECTAPPROVED
2012-02-13 23:52:19rev. 6CORRECTAPPROVED
2012-02-24 09:37:50rev. 6CORRECTAPPROVED
2012-03-26 20:02:57rev. 6CORRECTAPPROVED
2012-04-03 20:30:32rev. 6CORRECTAPPROVED
2012-04-19 17:24:17rev. 6CORRECTtested with Cisco Aironet 1131AG and worksAPPROVED
2012-05-11 07:26:27rev. 6CORRECTAPPROVED
2012-05-28 18:21:45rev. 6CORRECTAPPROVED
2012-06-19 16:48:32rev. 6CORRECTAPPROVED
2012-07-26 11:41:01rev. 6CORRECTAPPROVED
2012-08-18 16:23:33rev. 6CORRECTThe information is correctAPPROVED
2012-08-27 23:02:16rev. 6CORRECTAPPROVED
2012-10-11 06:54:48rev. 6CORRECTNo. old lenson is coming down and ill tell ya now.! senback aint guna b their!!!!!!APPROVED
2012-11-02 05:05:05rev. 6CORRECTAPPROVED
2012-11-07 04:00:06rev. 6CORRECTAPPROVED
2013-05-22 16:54:34rev. 6CORRECTAPPROVED
2013-07-25 20:36:53rev. 6CORRECTAPPROVED
2013-08-21 17:03:51rev. 6CORRECTAPPROVED
2013-10-20 19:00:06rev. 6CORRECTAPPROVED
2014-04-18 18:01:13rev. 6CORRECTAPPROVED
2014-05-06 15:30:09rev. 6CORRECTAPPROVED
2014-07-25 13:01:11rev. 6CORRECTAPPROVED
2014-11-22 02:48:42rev. 6CORRECTAPPROVED
2015-09-05 09:51:34rev. 6CORRECTAPPROVED
2016-04-19 13:21:02rev. 6CORRECTAPPROVED
2016-07-05 14:13:28rev. 6CORRECTAPPROVED
2016-08-17 22:47:46rev. 6CORRECTI tested this with my Cisco management cable and found results entirely consistent with your information here.APPROVED
2018-06-09 01:05:48rev. 8CORRECTAPPROVED
2018-07-31 12:15:14rev. 8CORRECTAPPROVED
2018-08-03 12:08:18rev. 8CORRECTAPPROVED

History of users contributions

Date Content
Author Comment
2008-07-11 22:50:57rev. 3There is no essential change, except that the ground wires of the DB9 are used to supress noise in cables 5 and 4 of the RJ45 jack. This could improve signal quality and raise baud rates.
2008-10-07 21:10:14rev. 4
2008-10-07 21:10:39rev. 4
2008-10-20 10:38:37rev. 4munter100Just wantred to add the last bit of the puzzle
2009-05-13 22:12:16rev. 5Colours copied from cable.
2010-02-27 22:30:37rev. 6JonChanged 2nd connector from female RJ-45 to male RJ-45 as this is a description of the cable.
2012-10-06 21:11:28rev. 6
2013-01-04 22:05:51rev. 6

Back to Cisco Console (9) cable pinout

Pinouts.ru > Pinout of Cisco Console (9) cable and layout of 9 pin D-SUB female connector and 8 pin RJ45 (8P8C) female connector
should be correct