Кабель для APC BackUPS BE350C,BE500C,ES 550 specification users reports and reviews |
Date | Content Revision |
User opinion | Comment | Approved by moderator? |
---|---|---|---|---|
2008-08-31 18:11:50 | rev. 2 | INCORRECT | Does not work. | APPROVED |
2009-02-25 19:56:17 | rev. 2 | CORRECT | This is correct as is, I just built a cable based on this and it works with the Back-UPS CS 500. Since I was using an 8 pin RJ45 (ethernet cable), I had to wire 1,7,6,3 instead of the 2,8,7,4 but this should be obvious... Thank you! | APPROVED |
2009-07-10 00:48:54 | rev. 2 | CORRECT | It works. I used 8P8C connector instead of 10P10C and 1,7,6,3 pins. | APPROVED |
2009-09-11 23:56:44 | rev. 2 | INCORRECT | Tried using the pins 1,7,6,3 suggested for rj45 8 pin, and could not interface with PowerChute software. Tested on apc back UPS-CS 650 | APPROVED |
2009-09-24 10:53:23 | rev. 2 | CORRECT | It works. I used RJ45 8p8c pins 1,7,6,3. Back-UPS CS 350 with MikroTik RB450. | APPROVED |
2010-05-30 13:20:47 | rev. 2 | INCORRECT | Back-UPS CS 350 does not respond to any commands. there is not smart capability and serial works only with APC 940-0128A cable or clones | APPROVED |
2011-01-18 13:36:04 | rev. 4 | INCORRECT | Does anyone know what resistor value(s) do I need to use for this cable to work? | APPROVED |
2012-03-23 02:42:38 | rev. 6 | INCORRECT | Resistors and diode values are missing. | APPROVED |
2015-07-27 15:35:19 | rev. 11 | CORRECT | I modify to rj45 and it's work! | APPROVED |
2017-08-13 16:59:16 | rev. 12 | ERROR FIXED | Hi, Tried in standard and nullmodem setup to connect with Tera Term VT to an AP9619 network card but after many hours trying, zero results. connection settings 8n1 no flow 2400baud connected only 4 cards The network card can't be found with an ip-sniffer and I get a black dead screen with the terminal programm.... Any help would be appreciated highly!! Kind regards Paul | APPROVED |
2018-09-19 00:39:33 | rev. 12 | ERROR FIXED | эта схема на 2 транзисторах http://www.reinhardweiss.de/pictures/backups/apc-940-0128d.gif https://www.youtube.com/watch?v=hIgTlk8HQgY | APPROVED |
2020-05-18 14:16:18 | rev. 12 | CORRECT | USB connection pinout worked. Could not get serial pinout to work. | APPROVED |
Date | Content Revision |
Author | Comment |
---|---|---|---|
2010-08-15 21:32:41 | rev. 2 | Wandrew | RJ45 is 8P8C and RJ50 is 10P10C |
2011-01-04 16:39:12 | rev. 4 | Criggie | Minor correction |
2011-10-04 22:50:41 | rev. 5 | MilK | really true pinout for BackUPS 550Es and other |
2012-10-06 21:42:25 | rev. 7 | ||
2012-11-23 22:00:28 | rev. 7 | You missmatched pins for white and green wire for USB cable |
Pinouts.ru > Pinout of APC BackUPS CS/ES smart signalling cable and layout of 9 pin D-SUB female connector and 10 pin RJ50 (10P10C) male connector |
unknown |